My Cart

size guide


Our model has a neck circumference of ca. 36cm (14.2 inch). For a similar effect, please bear in mind that the necklace will hang shorter (or longer), if your neck is wider (or smaller).

Necklaces of 60 cm (23.6 inch) length or longer will fit comfortably over the head without closure – with a length of 55cm (21.7 inch) or shorter, the necklace will need a closure to be put on.

The size/length details of our pieces are always without pendants.


Our ring sizes correspond with the French ring sizes:

XXS = 49

XS = 52

S = 54

M = 60

L = 65

XL = 68


It is best to have your ring size measured at a jeweler with a professional ring measuring tool.

If there is no chance to have the ring size measured professionally, please contact us and we can send you a ringsizer.

To measure with this, please follow the instructions below:

Wrap the ringsizer around the base of your finger and pull the end through the slot. Through the magnifying glass your ring size is shown. For a precise measurement, the tape measure should sit comfortably on the finger. To guarantee a perfect fit, pull the strap only as tight as you can still move the ringsizer over the joint of your finger.

If the measurement result is between two sizes, we recommend choosing the larger size.


The finger circumference may vary depending on the time of day and the temperature. Therefore, you should measure several times at different times of the day and on different days and then compare the values.

The fingers of right and left hand have usually different sizes – depending on whether you are left-handed or right-handed.

Do not measure your fingers when they are cold or wet as they might be smaller than usual.


If you already know the US / French / Japanese / British / etc. ring size or the circumference, please let us know. We can convert the international ring sizes into our size system.

In case you don’t know the ring size, you may:

1. ask the giftee

2. borrow a ring from the recipient that is similar in size and width to your desired model. Then you can try to measure the inner circumference with a strap of paper and tell us the length (in mm)

3. in case neither of the above is an option, guess the size: the average size for women is S. The average size for men is M.


Our rings are always made to felt size, because the width is not the same at every point, especially in the winding rings. This has already been taken into account during the development of the model. So, they might have a different size but, they feel like size XXS, XS, S, M, L or XL.


All rings have a slightly different size and only the ring on top has the exact size you need (that's how it is meant to be).

This ring will hold the other rings which are little looser. If all rings had the size of the top ring, it wouldn´t be comfortable to wear them. And the fact that they have different sizes gives the whole combination a good dynamic.

To wear the rings separately will probably not work, as they might be too big.


For most rings, it is possible to upsize the ring size slightly in the future, for sure one size, maybe even two sizes. Yet, this would be the maximum for upsizing.

Scaling down the ring size is not always possible and may not be offered for all ring models.

In case you need further help, please feel free to contact us.


Depending on the design, each bangle or bracelet will fit tighter or more loose, so the measurements below should guarantee a perfect fit.

For bracelets generally, the size depends in the wrist measurements.

XS - is for a wrist between 5.3-5.9 inch/ 13,5-15cm.

S – is for a wrist between 6.1-6.5 inch/ 15,5-16,5cm.

SM – is for a wrist between 6.6-6.8 inch/ 16,6-17,4cm.

M – is for a wrist between 6.9-7.3 inch/ 17,5-18,5cm.

L – is for a wrist between 7.5-8.0 inch/ 19-20,5cm

Please measure your wrist tightly, as indicated in the picture.

If you don’t have a tailor’s measuring tape at hand, please use a strip of paper or a ribbon instead, mark the wrist circumference on it and measure afterwards lying flat.


With a tape measure you simply measure the circumference of the trousers (without belt) in the loop area of ​​the trousers (on which you want to wear the belt).

The measurement result rounded down to 5cm or 0cm is your belt measure (the leather will stretch slightly with use).

Size S = ca. 85cm/33.5 inches.

Size M =ca. 90cm/35.4 inches.

Size L = ca. 95cm/37.4 inches.

For further information, please send us an email or give us a call.